工业PLC控制七:总装接线图命名规则

1 GA (General Assembly) WD Naming Convention 总装接线图命名规则

General Assembly WD drawing names are based on the systems they are associated with. Each system in GA has an abbreviation that is use in the name.

总装接线图的名称是基于与之关联的系统。 在总装中的每个系统都有一个使用缩写的名字。

Abbreviations 缩写 System Description 系统描述
ABPT AIR BRAKE PRESSURE TEST 空气制动1压力测试
ACFL AC FILL 交流充电
ACRC AC RECLAIM 交流回收
AGVS AUTOMATIC GUIDED VEHICLE SYSTEM 自动导向车辆系统
ALGN ALIGNMENT 队列
BAPD BRAKE AIR PRESSURE DECAY 制动气压衰减
BATT BATTERY LOAD 电池负载
BCFS BODY CHASSIS FASTENING SYSTEM 车身底盘紧固系统
BCMS BODY CHASSIS MARRIAGE SYSTEM 车身底盘合装系统
BKPB BRAKE PROBE TESTER 制动探针测试仪
BRKE BRAKE EVAC & FILL 制动器排空和加注
BRKP BRAKE FLUID PROCESSOR 制动液程序
BRPT BRAKE PEDAL TEST 制动踏板测试
BSAR BODYSIDE APPLY AND ROLL DOWN SYSTEM 侧围应用和下滚系统
BSCA BODYSIDE CLADDING APPLY 侧围包层应用
BSDW BODYSIDE DRY WIPE 侧围干擦
BSFF BODYSIDE FRONT FLARE
BSMA BODYSIDE MOLDING APPLY 侧围成型应用
BSRD BODYSIDE ROLL DOWN 侧围下滚
COKP COCKPIT LOAD/UNLOAD 驾驶舱装载/卸载
CONS CONSOLE 控制台
CRDL CRADLE LOAD/UNLOAD 托架装载/卸载
CRFM CONDENSER RADIATOR FAN MODULE 冷凝器散热器风扇模块
CRNR CORNERS 角落
DAXL DRIVE AXLE 驱动轴
DECK DECK LID RAISE/LOWER 行李箱盖上升/下降
DICH DITCH MOLDING
DOCKxx LOADING DOCK LOAD/UNLOAD (xx DENOTES DOCK NUMBER) 装卸码头装卸(xx表示码头数量)
DORI DOOR RE-INSTALL 门重新安装
DORR DOOR REMOVAL 门拆卸
DORT DOOR TEST 门检测
DVTS DYNAMIC VEHICLE TEST (ROLL TEST) 车辆动态试验(横摇试验)
ELET ELECTRICAL TEST 电气测试
EXHT EXHAUST LOAD/UNLOAD 排气装载/卸载
FAFL FRONT AXLE FLUID FILL 前轴注液
FAST FASTENING 紧固
FFPA FLUID FILL PRESENTATION ARM 注液显示臂
FMBH FOAM INJECTION BULK HANDLING 泡沫注射散装处理
FMIN FOAM INJECTION 泡沫注射
FMLD FOAM MODULE LOAD 泡沫模块加载
FPIT FLEX PLATE INDEX TOOL 柔性板索引工具
FTNK FUEL TANK 油箱
FUFL FUEL FILL 燃料填充
FUWS FUEL AND WINDSHIELD FILL SYSTEM 燃料和挡风玻璃填充系统
GEPS GLOBAL ERRORPROOFING SYSTEM 全球防错系统
GLAS GLASS INSTALL 玻璃安装
HEDL HEADLINER
HLA HEADLAMP AIM 前大灯瞄准
HOOD HOOD RAISE/LOWER 前盖升/降
HUBS HUBNIT SECURE
LGOF LIFTGATE DOCKING STATION OFF 后举门对中台关闭
LGON LIFTGATE DOCKING STATION ON 后举门对中台打开
LIFG LIFTGATE 后举门
LMSC LMS CHASSIS
LMSD LMS DOORS
LMSE LMS ENGINE
LMSP LMS COCKPIT
LMST LMS TRIM
MDBK MD BRAKE TESTER
MH MATERIAL HANDLER 仓库管理员
PBTA PARK BRAKE TENSIONING ADJUST 驻车制动器张紧调整
POWT POWERTRAIN LOAD/UNLOAD 动力系统加载/卸载
PROP PROP SHAFT 支撑轴
PSFL POWER STEERING FILL 动力转向系统加注
PSTR POWER STEERING & TRANSMISSION FILL
RAFL REAR AXLE FLUID FILL 动力转向和变速箱加注
RDAC RADIATOR & AC FILL 散热器和空调加注
RDFL RADIATOR FILL 散热器加注
RDRD ROOF DITCH ROLL DOWN
RHCM CRFM RACK HANDLER
RHEN ENGINE RACK HANDLER
RHFT FUEL TANK RACK HANDLER
RHHK HUB KNUCKLE RACH HANDLER
RHHT (RETRACTABLE) HARD TOP RACK HANDLER
RHIR INDEPENDENT REAR SUSPENSION RACK HANDLER
RHRS REAR SUSPENSION RACK HANDLER
RHTR TRANSMISSION RACK HANDLER
ROFM ROOF MODULE
SEAT SEAT LOAD/UNLOAD
SARS SQUEAK AND RATTLE SYSTEM
SUNR SUNROOF
SUSP SUSPENSION
TIER TIE RODS
TPMD TTIRE PRESSURE MONITOR DATA EXTRACTION
TPMI TIRE PRESSURE MONITOR INSTALLATION
TPMV TIRE PRESSURE MONITOR VERIFICATION STATION
TRAB TIRE ROOM AUDIT BALANCERS
TRBS TIRE ROOM BARCODE STATION
TRDC TIRE ROOM DELIVERY CONVEYOR
TRFL TRANSMISION FILL
TRMI TIRE ROOM MOUNT & INFLATE
TRPB TIRE ROOM PRIMARY DYNAMIC BALANCERS
TRSO TIRE ROOM SOAPERS
TRST TIRE ROOM STEMMER
TRTK TIRE ROOM TRACKER
TRVS TIRE ROOM VISION SYSTEM
TTOF TRANSMISSION TOP OFF
UCAL UPPER CONTROL ARM LEFT HAND
UCAR UPPER CONTROL ARM RIGHT HAND
VAST VEHICLE AUDIO SYSTEM TEST
VINC CRASH CART VIN MARKER
VINE ENGINE / TRANSMISSION VIN MARKER
VINP PRIMARY VIN MARKER
VINS SECONDARY VIN MARKER
WATR WATER TEST
WHLT WHEEL & TIRE MULTIPLE
WIPM WIPER MODULE
WIRE WIRE HARNESS
WWFL WINDSHIELD WASHER FLUID FILL

2 Controller Level WD Naming Convention 控制级接线图命名规则

character department code,4 character system code, and 2 digit sequence (specified by the project controls engineer).
字符部门代码、4字符系统代码和2位数字序列(由项目控制工程师指定)。

Example GA Controller Level WD:
Trollhattan Assembly Plant (TH)
General Assembly (GA)
AC Fill System (ACFL)
Sequence Number (03)
Controller Level wiring diagram = WD-TH-GA-ACFL03

示例总装控制级接线图:
Trollhattan Assembly Plant (TH)
总装(GA)
空调加注系统(ACFL)
序号(03)
控制级接线图= WD-TH-GA-ACFL03

3 Tool (Unit) Level WD Naming Convention 单元级接线图命名规则

The unit WD name is created by a “WD-“ prefix, 2 letter code of the using plant, 2 character department code, mechanical tool number, and 2 digit sequence (specified by the project controls engineer).
单元级接线图命名由“WD-”前缀、使用工厂的2个字母代码、2个字符的部门代码、机械工具编号和2个数字序列(由项目控制工程师指定)创建。

Example GA Tool (Unit) Level WD:
Trollhattan Assembly Plant (TH)
General Assembly (GA)
Mechanical Tool Number (T77635)
Sequence Number (01)
Unit Level wiring diagram = WD-TH-GA-T7763501

GA单元级接线图示例:
Trollhattan Assembly Plant (TH)
总装(GA)
机械工具编号(T77635)
序列号(01)
单元级接线图=WD-TH-GA-T7763501