工业PLC控制五:车身车间接线图命名规则

1 Naming Conventions 命名规则

Cells (gated/fenced area) shall be numbered with the same number as the first station controlled by the cell. For mainline cells, use the first mainline station in the cell.

单元(门控/围栏区域)的编号应与单元控制的第一个工作站的编号相同。 对于主线单元,请使用单元中的第一个主线工作站。

Example: The cell that controls stations 12, 15, and 20 shall be CELL #15.
示例:控制站12,15和20的单元应为CELL#15。

Figure 1 Cell Numbering Convention.jpg

2 System Level WD Naming Convention 系统级接线图命名规则

Bodyshop systems are groups of cells referred to as Zones. These zones are designated by letters (see GEP1, Global Engineering Process Standards). There are many zones within the bodyshop. A system WD typically covers several zones or subzones. The system WD starts with “WD-“, followed by the 2 letter code of using plant, year, and primary zone number. The year is the intended start of regular production (SORP) of the equipment, not the model year. The primary zone number is the first zone covered by the system drawing.

车身车间系统是一组称为区域的单元。这些区域由字母指定(参见GEP1,全球工程工艺标准)。在车身车间中有许多区域。一个系统WD通常包括几个区域或子区域。系统WD以“WD-”开头,然后是使用的工厂、年份和主区号的2个字母代码。该年是设备常规生产(SORP)的预期开始,而不是模型年。主区域号是系统图中覆盖的第一个区域。

Example Bodyshop System:
Covering Process Zones BA_B01, BB_B01, and CD_B01
Fairfax Plant (FA)
2008 start of Production (08)
System Zone level wiring diagram = WD-FA08BAB01

示例车身车间系统:
覆盖工艺区域BA_B01, BB_B01, CD_B01
Fairfax Plant (FA)
2008年投产 (08)
系统区域级接线图 = WD-FA08BAB01

3 Controller Level WD Naming Convention 控制级接线图命名规则

The control WD number shall be the 1st process station number in the cell or safety area (specified by the Process Engineer in compliance with GEP1, Global Engineering Process Standard) with a “WD-” prefix, 2 letter code of using plant, and SORP year.

控制级接线图编号为单元或安全区域的第一个工艺工作站编号(由工艺工程师按照全球工程工艺标准GEP1规定),前缀为“WD-”,使用工厂的2个字母代码,SORP年份。

Figure 2 Process Cell Naming Convention From GEP1.jpg

Example Bodyshop Controller(Cell) Level Drawing:
Process Cell AB030_B01
Lansing Delta Township Plant (LD)
2009 start of Production (09)
Cell Level wiring diagram = WD-LD09AB030B01

示例车身车间控制(单元)级别图:
工艺单元 AB030_B01
Lansing Delta Township Plant (LD)
2009年投产(09)
单元级接线图= WD-LD09AB030B01

4 Tool (Unit) Level WD Naming Convention 工具级接线图命名规则

For Bodyshop tooling there is typically one WD drawing per tool. This drawing is commonly referred to as the tool WD. The tool WD drawing number is created by adding a “WD-“ prefix and a zone station number suffix to the mechanical tool number. The tool number is assigned by the Process Engineer.

对于车身车间工具,通常每个工具有一个接线绘图。这张图通常称为工具接线图。工具接线绘图号是通过在机械工具号中添加“WD-”前缀和区域站号后缀来创建的。工具号由工艺工程师指定。

Example Bodyshop Tool (Unit) level WD:
Tool number MAA13998S
Station number BA030B1
Tool level WD package = WD-MAA13988S-BA030B1

示例车身车间工具(单元)级别图:
工具号 MAA13998S
工作站编号 BA030B1
2009年投产(09)
工具级级接线图= WD-MAA13988S-BA030B1